3D Printing Doctor Who - Print and paint your own 5.5" scale customs

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

Doctor What wrote:
Sat Nov 30, 2019 11:49 pm
These look excellent, i've been looking into getting a 3D printer soon and the thought of having a little cleaner robot to go with my figures is making me want one even more!

I've read your first post on this topic about printers but I was wondering if there are any you would specifically recommend, probably in the "lower" price bracket of 3D printers of up to about a maximum of £300?
If you're in the UK, about the only filament printer that's under £300 is the £260 Creality Ender 3 Pro. A lot of people use these and while it's only a standard 100 micron resolution printer, it does have some nice features like a built-in auto-resume if your power happens to flicker or go out, and an extremely large print area that can print even the biggest of my figures.

You can also get an Anycubic Photon, the same resin printer that I use, for £299 (possibly cheaper if you find it on sale or through eBay) or the Elegoo Mars for £229, both of which print at insanely high detail, though keep in mind that if you go with resin, there are all the usual safety concerns that you'll want to think about (do you have small kids or pets for whom potentially toxic chemicals would be a danger) and that you'll probably be spending twice as much as you thought to set up your dedicated print area which will need to have a sturdy table with room for beakers or mason jars to rinse your prints in isopropyl alcohol, a box of Nitrile Gloves, lots of paper towels, a scrubbing tub with water and a toothbrush or an ultrasonic cleaner (about £25) to clean off any excess IPA and resin, ziplock bags for storing your cast-off resin (which must be set outside to cure in the sun before your throw it away), a large trashcan with a lid, and a small UV Cure light (also about £25) to give your parts a final curing before they're ready for painting.

If you're printing indoors, especially around where you sleep, eat, or spend a lot of time, expect the initial setup cost to go up even higher as you'll almost certainly want to purchase some sort of cabinet to house your printer/bottles of resin, possibly with some kind of inline duct fan/dryer hose arrangement to whisk fumes away outside or to a dryer vent, and some large heavy duty vinyl chair mats if you're printing anywhere near carpet or floors that you don't want to see damaged by potential resin spills. (I can guarantee, no matter how careful you are, you will be dripping resin at some point)

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

Image

Fresh off the printer!
This is a big 'un and I had less than 1mm to spare on either side in my Anycubic Photon FEP vat. I'm glad it turned out okay.
I'm printing the front half of the base now. I'm really glad that resin printers are so fast, and even my biggest pieces never take more than about 24 hours to finish. (though I did have to top up the resin part-way through)

User avatar
skifflebits
Posts: 1061
Joined: Tue Jun 11, 2019 2:41 pm

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by skifflebits »

Looking good!
None of Doctor Who is canon.

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

Well, I'm awfully glad I didn't spend any time on the Recon Dalek so many of you were asking for.
I figured CO would get around to it as soon as they could scrape together enough cash, and I was right. It's part of the new wave being released February-ish.

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

Image

Almost finished printing the Cleaner!

Only the bottom half of the wheelie bin is left to do in white, then the wheels, boots, and internal mounts to do in black. I should be ready to paint by the weekend. I’ve made a couple of extremely minor modifications to the design (shaving half a mm off here and there on parts that I had to sand down on my prototype print) but otherwise I’m quite proud of myself for creating my first “one and done” figure that's also fully articulated.

User avatar
DalekCheese
Posts: 3553
Joined: Wed Jun 12, 2019 4:54 pm
Location: Mondas

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by DalekCheese »

And now: paint.
AI is here!!

User avatar
Merlin
Posts: 122
Joined: Thu Jun 13, 2019 8:53 am

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by Merlin »

3DPrintingDoctorWho wrote:
Thu Dec 12, 2019 9:22 am
Image

Almost finished printing the Cleaner!

Only the bottom half of the wheelie bin is left to do in white, then the wheels, boots, and internal mounts to do in black. I should be ready to paint by the weekend. I’ve made a couple of extremely minor modifications to the design (shaving half a mm off here and there on parts that I had to sand down on my prototype print) but otherwise I’m quite proud of myself for creating my first “one and done” figure that's also fully articulated.
Holy mother of god, that is gorgeous.
No forum, no matter how great, can know it’s destiny. It cannot glimpse his part in the great story that is about to unfold. As it will be for the member arriving at the gates of DWT.net. A lad that will, in time, father the legend. His name: Merlin.

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

It's been a few months, so I put together a new video talking about the project over the weekend. Nothing groundbreaking that most of you don't already know about, but it helps get the word out to fans who aren't familiar with the project. Plus, if I can get 13 more subscribers, YouTube will give me a custom channel URL, which will make it a hell of a lot easier to link to in my sig files.

https://youtu.be/HYmVVGi0orA

User avatar
skifflebits
Posts: 1061
Joined: Tue Jun 11, 2019 2:41 pm

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by skifflebits »

Subscribed!
None of Doctor Who is canon.

User avatar
3DPrintingDoctorWho
Posts: 78
Joined: Wed Jun 12, 2019 6:08 am
Location: Sacramento, CA
Contact:

Re: 3D Printing Doctor Who - Print and paint your own 5.5" scale customs

Post by 3DPrintingDoctorWho »

For anybody on here that is considering designing their own figures or custom parts for SLA resin printing (i.e. using an Anycubic Photon or similar) I've uploaded the rotational joint design I've been using for my latest batch of figures to TinkerCAD for anybody who wants to play around with it.

https://www.tinkercad.com/things/bkF799ud6zS

You can use this sheath design for shoulders, necks, wrists, ankles, or any other parts that need to spin in a socket, where you don't want to have to split your entire figure down the middle to insert a ball joint. I've shrunk this design down as small as 8mm and still had it work, and you should be able to scale it up as large as it needs to go.

I'm slowly working backwards and incorporating this into all my 3D printable figures, but for anybody who wants to create their own (or adapt a solid sculpture that you've found elsewhere) here are just the peg, hole, and sheath parts for you to play around with. You might even be able to adapt this for customizing existing Character options toys with a custom 3D printed head/arm/etc. if you can drill out the neck or shoulder to be the same width as the sheath.

Post Reply